PLEASE KEEP THESE INSTRUCTIONS FOR FUTURE REFERENCESHERWOOD INDUSTRIES IS AN ENVIRONMENTALLY RESPONSIBLE COMPANY. THIS MANUAL IS PRINTED ON RECYCLED P
10Installation of firebox backing:• Install the side panels in place. Insert center panel, hold the panels in place• Install the top rod by sliding i
11InstallationDECIDING WHERE TO LOCATE YOUR PELLET APPLIANCE:1. Check clearances to combustibles.2. Do not obtain combustion air from an at
InstallationDIMENSIONS - FREESTANDING:
13InstallationCLEARANCES TO COMBUSTIBLES - FREESTANDING:When installing this unit on a combustible floor (for example linoleum, hardwood f
14InstallationCLEARANCES TO COMBUSTIBLES - BUILT-IN HEATER:Refer to Figures 11 and 12.Side wall to unit - 8 inches (20.3 cm)Mantel projection -
15become hot enough to cause burns if touched by children. Non-combustible shielding or guards may be required.3. Termination must exhaust above the
Outside fresh air is mandatory when installing this unit in airtight homes and mobile homes. When connecting to an outside fresh air source, do not us
17Figure 21: Corner Installation. InstallationMOBILE HOME INSTALLATION - FREESTANDING:1" (2.5cm)1"(2.5cm)6"(15 cm)Floor ProtectionFresh
InstallationHORIZONTAL EXHAUST THROUGH WALL INSTALLATION - FREESTANDING:Vent installation: install vent at clearances specified by the vent manufactur
19Installation10. The pipe must extend at least 12” (30 cm) away from the building. If necessary, bring another length of pipe (PL type) to the outsid
Table of Contents2Introduction...
InstallationINSIDE VERTICAL INSTALLATIONS - FREESTANDING:1. Choose a stove location that is ideal. See the section “DECIDING WHERE TO LOCATE YOUR PE
21InstallationNon-combustiblefloor protection.Existing floor(combustible)6"(15cm)Rain capFlashing24"(61cm)1"(2.5cm)Tee withcleanoutFres
Installation
23
Non-combustiblefloor protection.Existing floor(combustible)6"(15 cm)3" (7.5 cm)PedestalWallthimbleFresh airintakeRodentmesh cap45°elbow12&qu
Installation25Figure 34: Corner brackets for trim.Figure 35: Two pieces of corner bracket.4. Plug the wiring harness into the control panel (see Figur
InstallationSLIDER/DAMPER INSTALLATION:This is used to regulate the airflow through the pellet stove.1. Remove the slider rod (short rod with
27TroubleshootingDO NOT:● Service the stove with wet hands. The stove is an electrical appliance, which may pose a shock hazard if handled improperl
Troubleshooting● Check Vacuum levels in the exhaust channel by bypassing the Vacuum Switch, then remove the Vacuum hose from Vacuum Swi
29Troubleshooting6. The auger motor will not function normally.● If the Auger gear box does not turn but the motor’s armature does try to spin
3IntroductionPELLET QUALITY:Pellet quality is important, please read the following:Your enviro pellet stove has been designed to burn wood pellets onl
8. The 200°F (93°C) high limit temperature sensor has tripped.● Reset the sensor and determine the cause - was it convection blower or 160°F (71°C) t
31Wiring DiagramTIMER CONTROL:YellowYellowPurplePurpleOrangePowerCordBrownBrownRedIgnitor120oF (49oC)IgnitorTemperatureSensor160oF (71oC)ConvectionTem
Parts ListReference NumberDescription Part NumberFreestanding Fan Controller Knob EC-040Power Cord - 115V EC-0421 Auger Motor - 115V EF-0012 Convecti
33Reference NumberDescription Part NumberFirebox Liner Top Plate EF-066Dial-a-Fire Knob EF-067” ID Auger Collar with Set Screw EF-069Knob 1 Inch Roun
Parts ListReference NumberDescription Part Number43 Control Panel Touch Latch 50-32344 Combustion Blower Exhaust Tube 50-32745 Stainless Steel Burn Po
35Parts Diagram - ComponentsEF3 - Components (115V)September 2006
Parts Diagram - SteelEF3 - Steel Components (220V)September 200636
37WarrantySherwood Industries Ltd. gives a five year limited warranty on all steel manufactured parts. A one-year warranty is provided on all electri
38The following information must be recorded by the installer for warranty purposes and future reference.NAME OF OWNER:_______________________________
4IntroductionIMPORTANT SAFETY DATA:Please read this entire Owner’s Manual before installing or operating your ENVIRO Pellet Stove. Failure to follo
5IntroductionASHES: Disposed ashes should be placed in a metal container with a tight fitting lid. The closed container of ashes should be on a non-co
6Operating InstructionsAUTOMATIC SAFETY FEATURES:Your pellet Stove has the following safety features:A. The stove will shut off when the fire
7Operating InstructionsOPERATING YOUR PELLET STOVE:Figure 3: Dial-A-Fire control panel. 1. Check and fill hopper with pellets.2. Make sure unit is p
8Routine Cleaning and MaintenanceNOTE: Do not use abrasive cleaners to clean the surface or any part of the stove.The following should be inspected pe
9ASH PAN (2-3 days)Monitor the ash level every week. Remember that different pellet fuels will have different ash contents. Ash content is a good ind
Commentaires sur ces manuels